Curing Tank

Curing Tank for up to 30x150mm Concrete Cubes, made from Polyethylene and measuring 990x686x635mm overall. It is fitted with a 220 volt 3kW Heater but also works on 110v (heating taking a little longer), fitted with mechanical thermostat and a galvanised mesh lower rack. The thermostat is factory set to control the Tank at 20 deg C. It is ideal for site use where an economical solution is required.

EN12390-2

Large Curing Tank for up to 75 x 150mm Concrete Cubes, made from Polyethylene and measuring 120x100x76cm overall. It is fitted with a 3kW Heater, Electronic Controller with digital display and galvanised mesh lower racks. The controller is factory set to control the tank at 20 deg C. It is ideal for site use or where an economical solution is required.

EN12390-2

Large Curing Tank for up to 75 x 150mm Concrete Cubes, made from Polyethylene and measuring 120x100x76cm overall. It is fitted with a 3kW Heater, Electronic Controller with digital display and galvanised mesh lower racks. The controller is factory set to control the tank at 20 deg C. It is ideal for site use or where an economical solution is required.

EN12390-2

Specimens must be cured at a stable temperature under water to ensure
consistent test results. Temperature control on our tanks is extremely accurate, exceeding the most stringent requirements. Tank features:
* Galvanised Steel Construction.
* Rack Supports folded into sides for strength & easy cleaning.
* Drain Valve.
* Magnetic Drive pump.
* Electronic Controller.
* Capacity 100x150mm Cubes
* Dimensions 1750x850x550mm (800lt)

Specimens must be cured at a stable temperature under water to ensure
consistent test results. Temperature control on our tanks is extremely accurate, exceeding the most stringent requirements. Tank features:
* Galvanised Steel Construction.
* Rack Supports folded into sides for strength & easy cleaning.
* Drain Valve.
* Magnetic Drive pump.
* Electronic Controller.
* Capacity 100x150mm Cubes
* Dimensions 1750x850x550mm (800lt)

Specimens must be cured at a stable temperature under water to ensure
consistent test results. Temperature control on our tanks is extremely accurate, exceeding the most stringent requirements. Tank features:
* Galvanised Steel Construction.
* Rack Supports folded into sides for strength & easy cleaning.
* Drain Valve.
* Magnetic Drive pump.
* Electronic Controller with Cooling Output
* Capacity 100x150mm Cubes
* Dimensions1750x850x550mm (800lt)

Specimens must be cured at a stable temperature under water to ensure
consistent test results. Temperature control on our tanks is extremely accurate, exceeding the most stringent requirements. Tank features:
* Galvanised Steel Construction.
* Rack Supports folded into sides for strength & easy cleaning.
* Drain Valve.
* Magnetic Drive pump.
* Electronic Controller with Cooling Output
* Capacity 100x150mm Cubes
* Dimensions1750x850x550mm (800lt)

This procedure is used for the curing of concrete specimens under conditions intended to accelerate the development of strength.
The tank will maintain a constant temperature of 55+/- 1 deg C. Designed for hot water curing of concrete specimens, this is a very robust galvanised steel tank c/w lower rack and lid. It comes complete with a temperature chart recorder (which can also be ordered separately).

External Dims 90x85x50cm
Capacity 50x 150mm Cubes
Electrical 415/440 volt 50Hz 3 phase 12kW

A Water Chiller unit with Heat Exchanger and all accessories to use with our CT3 Curing Tank. This unit will prevent Curing Tank temperature increasing above standard parameters in ambient temperatures above 20C.

An economic cooling system for use with our CT3 CuringTank. This system introduces mains water to the tank when required to lower temperature.
A mains water supply cooler than 20C and a drain for overflowing water are essential.

Curing Tank 1750x850x550mm without heater, controller and pump for use with Linking Kit

For use with CT2 and CT3

A kit of all parts needed to link our CT2 or CT3 to a second plain tank (CTGALVTANK).
A large part of the cost of a curing tank is the controller, heater and pump. Linking 2 tanks is an economic way to increase tank capacity. We have found that up to 3 additional plain tanks can be connected to a CT2 or CT3.

For use with CT2 &CT3

Controller, Pump, Heater and all accessories to update an existing tank

Controller, Pump, Heater and all accessories to update an existing tank. Controller has output for Cooling.